The job of queue_output_config is now just to fill out a
wlr_output_state according to the output configuration, but it still has
a lot of logging from before we had wlr_output_state or the new modeset
logic, when queue_output_state instead touched the implicit pending
state of wlr_output.
Whatever debug logs it had would already be covered by the output state
debug logs or the command debug logs, so let's just remove it.
Starting by setting some special initial output config values settings
was something sway used to do when the config was initially being
processed. This was later changed to always happen, as there shouldn't
be differences in how output config is calculated during config load and
after.
Most of these values are redundant, as they are either the zero value or
a value that would be selected if the unset (-1) value was found.
For output transforms, the automatic panel orientation code would only
trigger if the final output config has an unset transform, which the
initial values set in find_output_config made impossible.
Remove these initial values and instead use a fresh output config as is.
queue_output_config had some remaining logic that would avoid setting
output states if they already appeared to be in effect. That is not what
most of the states did nor what is currently expected, so clean that up.
switching workspace directly to urgent window creates timer which delays
reset of urgent state so user is able to notice it. make sure state
change is reflected visually as well (border change) by triggering
container update
Fixes: #8377
Man sway(5) specifies that when tiling_drag is enable, the floating_mod
can be used to drag tiling, as well as floating containers. However the
current code indiscriminately assumes any button press to be intended
for moving the container, consequently causing an unintended call to
`seatop_move_tilting:handle_button` rather than
`seatop_default:handle_button` to pass
`state=WL_POINTER_BUTTON_STATE_RELEASED` to `get_active_mouse_binding`
My idea was to make 'Handle moving a tiling container' follow the same
path as 'Handle moving a floating container' because the initial call to
handle moving a floating correctly exits that branch and ends up passing
the RELEASED state to `get_active_mouse_binding`.
Fixes#8334
in pr https://github.com/swaywm/sway/pull/8196, when im_popup_surface is unmapped, author set the popup->relative to NULL, butt popup is still in popup groups, where assert the relative is not NULL, this cause the panic
Take the suggestion of Nefsen402, remove the line where set relative to
NULL, and add NULL check in scene_descriptor_destory
sway_root.outputs only include enabled outputs. We also need to re-init
the renderer for any disabled outputs, so use sway_root.all_outputs
instead.
Resolves the following heap-use-after-free accessing the render formats
when a disabled output is modeset after a GPU reset has occurred.
Currently, swaybar does not gracefully die if it detects
that the dbus connection was lost. Although it's not recommended
to restart dbus without restarting the compositor, it can very
easily happen. In the case it does, compositor's tray should
not consume 100% cpu until it has to be force killed.
apply suggestions
just setting the bar to not running will call teardown and unref the
dbus.
We batch modesets and input configuration performed during config reload
but commit for every command during the intial config load. There is no
need to perform commits during the initial config load as outputs have
not yet been created, but swaybg spawn should still be batched.
At the same time, replace direct calls to apply output configuration
with request_modeset to properly handle the modeset timer.
GUD devices uses RGB565 by default for performance reasons. Allow
specifying render_bit_depth 6 to pick this format. The definition works
out if you consider the maximum number of bits per channel instead of
the average.
Arranging lock surfaces rely on the sway_output width and height being
updated, but these are only updated after the commit has been completed
and all commit listeners have executed. This means that the lock
surfaces will not be appropriately scaled to match a change in output
dimensions, and may reveal what is under the lock background.
Replace the implicit arrange through the output commit listener with an
explicit arrange after the output configuration is finalized.
This might have regressed by other transition away from output commit
listeners for other arrange tasks, but even then it would have
erroneously relied on signalling order.
Some display output hardware [1] doesn't support any of the current
formats, but works with ARGB8888. Fall back to it if available.
[1] 196145c606/drivers/gpu/drm/xlnx/zynqmp_disp.c (L313)
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Instead of using a single finalized output config per output, accept a
regular list of output configs like the one ultimately stored for
configuration purposes. This allows the output management code to test
an augmented configuration while still using the same output config
logic, without having to mutate the stored configuration.
This in turn allows us to make a few APIs private. A bug note about an
existing issue with derade to off is added as well.
We always need to start out with the default configuration, regardless
of whether the config is reloading or not to ensure that config
decisions are stable given a specific configuration.
Simplify find_output_config and inline the search through the output
configs instead of using list_seq_find with a comparator function. The
new implementation will merge any amount of matched configs in order,
which will be relied upon in a future commit.
Previously, we incorrectly only set active keyboard for non-virtual
devices. 4c3c060211 incorrectly put
unrelated code in `sway_keyboard_set_layout`.
Fixes: 4c3c060211
If the output is not active, it might not have a valid geometry to
arrange for. Outputs do not gain a geometry until modeset, so if an
output is connected with a configuration present to disable it, it will
not have a geometry. If the output has a past workspace restored, this
will be attemtped arranged to fit a 0x0 rectangle, which asserts when
trying to sort out borders.
Consider the workspace activated only if the output itself is active to
get the scene nodes disabled.
The else condition was missed here and we would never skip the % char
if it didn't end up matching with any property. Since we fail to skip
we would re-evaluate the % in an infinite loop never achieving any
forward-progress.
Fixes: https://github.com/swaywm/sway/issues/8333
Output layout changes originate from the centralized modeset
infrastructure and request_state which already takes care of arranging
and updating outputs as needed.
