The original purpose of this commit is to replace some for loops with
list_find. But while doing this I found the workspace_prev_next_impl
functions to be difficult to read and also contained a bug, so I
refactored them and fixed the bug.
To reproduce the bug:
* Have two outputs, where the left output has workspaces 1, 2, 3 and the
right output has workspaces 4, 5, 6. Make workspace 2 focused_inactive
and workspace 4 focused.
* Run `workspace prev`.
* Previously it would visit the left output, then apply `workspace prev`
to workspace 2, which focuses workspace 1.
* Now it will focus the rightmost workspace on the left output
(workspace 3).
The refactoring I made to the workspace functions are:
* Added the static keyword.
* They now accept an int dir rather than bool, to avoid an unnecessary
conversion.
* Rather than preparing start and end variables for the purpose of
iterating, just iterate everything.
* Replace for loops with list_find.
* Don't call workspace_output_prev_next_impl (this fixes the bug).
Commit 4b8e3a885b makes it so only one
transaction is committed (ie. configures sent) at a time. This commit
removes the now-unnecessary code which was used to support concurrent
committed transactions.
* Instead of containers storing a list of instructions which they've
been sent, it now stores a single instruction.
* Containers now have an ntxnrefs property. Previously we knew how many
references there were by the length of the instruction list.
* Instructions no longer need a ready property. It was used to avoid
marking an instruction ready twice when they were in a list, but this is
now avoided because there is only one instruction and we nullify the
container->instruction pointer when it's ready.
* When a transaction applies, we no longer need to consider releasing
and resaving the surface, as we know there are no other committed
transactions.
* transaction_notify_view_ready has been renamed to
view_notify_view_ready_by_serial to make it consistent with
transaction_notify_view_ready_by_size.
* Out-of-memory checks have been added when creating transactions and
instructions.
This fixes an issue where views might commit to a transaction ahead of
the first one, and applying the first transaction causes us to save a
buffer of the wrong size.
There was a separate function dispatch_cursor_button_floating which
dealt with the resize and move operations, but as resize is not really
limited to floating views, it doesn't make as much sense to have this
separate. So both functions are now combined into one.
Additionally, dispatch_cursor_button now uses a pattern of returning
early instead of using else-ifs.
* The OP_RESIZE seat operation has been renamed to OP_RESIZE_FLOATING,
and OP_RESIZE_TILING has been introduced.
* Similar to the above, seat_begin_resize and handle_resize_motion have
been renamed and tiling variants introduced.
* resize.c's resize_tiled has to be used, so container_resize_tiled has
been introduced in resize.c to allow external code to call it.
This allows for a color to be set when the wallpaper does not fill the
entire output. If specified, the fallback color is also used when the
image path is inaccessible.
Rationale: Sticky containers are always assigned to the visible
workspace.
The basic idea here is to check the destination's output (move.c:190).
But if the command was `move container to workspace x` then a workspace
might have been created for it. We could destroy the workspace in this
case, but that results in unnecessary IPC events.
To avoid this, the logic for `move container to workspace x` has been
adjusted. It now delays creating the workspace until the end, and uses
`workspace_get_initial_output` to determine and check the output before
creating it.
* Removes container_floating_move_to_container, instead opting to put
that logic in container_move_to
* In the seat code, focusing a floating view now updates the pending
state only and lets the next transaction carry it over to the current
state. This is required, otherwise it would crash.
* When unfullscreening a floating container, an output check is now done
to see if it should center it.
In a multi-output setup, if a sticky container is on one output and
focus is on the other output, and you run (eg) `workspace 1` to focus
the workspace containing the sticky container, an infinite loop would
occur. It would loop infinitely because it would remove the sticky
container from the workspace, add it back to the same workspace, and
then decrement the iterator variable.
The fix just wraps the loop in a workspace comparison.
